Assemble a Gas Pole Saw in 3 Steps Like It’s A Piece of Cake

A gas pole saw is important to cut hard-to-reach branches. Also, it’ll give you control over thick branches without running out of electricity. But before operating the saw, you have to assemble it, which brings the question of how to assemble a gas pole saw.

To assemble the gas pole saw, you have to attach the blade first. For the blade, you’ll find the screw setup on the top-rear side. You can use a screwdriver to tighten the blade.

However, that’s not it. There’s more to know. So scroll down to the end to get to know all the details. Let’s get started, then.

How to Assemble a Gas Pole Saw?

How to Assemble a Gas Pole Saw

To assemble a gas pole saw you have to know the following things. They are:

  • Check the Product

Checking the pole saw is definitely the first step because a pole saw’s blade is so sharp that you have to be careful. However, a defective pole saw poses a serious risk to the user. 

  • Assemble the Blade

For the proper assembly, you have to attach the blade to the pole. While attaching it, you have to ensure that you tighten the screw on the top rear side well enough because it’ll hold the blade’s position. 

  • Determine Stem

Do not attempt to remove an unlabeled section of the tree. Try to avoid picking a thick branch. It’s suggested that you prune the branches to a length of between 3 and 8 inches. 

Nevertheless, trouble and a dull saw blade are both possible while working with thick branches. It’s, therefore, essential to establish a strategy before using the saw on the branches.

Process of Using an Assembled Gas Pole Saw

Process of Using an Assembled Gas Pole Saw

Here are some steps that you can follow to use a gas pole saw. Let’s check out.

  • Make Space For Work

The first and foremost thing is to clear out the place for work. That’s why you should ensure that there’re no people or any valuables where you’ll cut down the tree limbs.

It’s important to keep your working space clear of any potential trip hazards so you can walk about the area with ease.

Roping off the area can prevent passersby from getting too close to your job if you’re doing it in a public place.

Moreover, make sure you know exactly where you want to cut the wood with the pole saw before you start chopping. You shouldn’t go hacking away at a tree without first planning out your strategy.

So, back up, take in the big picture, and think about which branches you want to prune.

  • Cutting Lower Branches

After making space, it’s important to plan how you’ll cut the higher branches. For that, you need to cut the lower branches fast so that you got smooth access to higher branches.

The next thing you should keep in mind that the position of your standing. So while using a pole saw, never stand immediately beneath it. However, If you take this stance, you will be less likely to be hurt when the trunk finally gives way.

Check that the pole saw’s end is comfortably within chest height. When using a pole saw, it’s best to do it at an incline.

  • Adjusting The Pole Length
Process of Using an Assembled Gas Pole Saw

After finding the right position, adjust the pole length so that you can cut the low branches by holding the pole saw at your chest level. You can check the owner’s manual for the guideline for adjusting the pole length.

  • Pole Saw’s Blade Position

Adjusting the blade’s position is as important as adjusting the pole length because if you don’t have enough control over the blade, it might cause severe accidents.

That’s why to hold your position tight and make sure you’ve full control over the pole saw’s weight. However, you can start cutting after you feel ready and secure.

  • Starting The Cut

The first thing you should keep in mind is that you should cut the branches slowly and carefully. And what’s the reason behind it? When you try to chop a branch at full speed straight out of the gate, the blade might slide and make the job more difficult.

However, making a trench in the wood is a sensible solution. When cutting a groove into a branch, take your time initially. The initial groove in the wood can be made by tapping or gently moving the throttle.

No wonder making a groove will guide you for faster strokes. Especially if the branch is slanted, you should know that the saw may move sideways while making these preliminary cuts.

When using a pole saw, if the blade slides, you must pause cutting and realign it before resuming. Now you can increase the strokes and finish your cuttings.

  • Clean Up The Space

Now that you have cut all the branches, it’s time to clean up all the branches that have fallen on the ground. One more thing, you can cut branches vertically for a better experience.

Safety Features to Consider While Assembling A Pole Saw

Safety Features to Consider While Assembling A Pole Saw

You’re dealing with cuts, blades, and other stuff that can cause you to harm if you’re not careful enough while cutting. That brings us to the next topic, which is safety measurements.

  1. Wearing protective gear is a must while cutting. The set consists of a protective headpiece, gloves, goggles, boots, and a loose-fitting dress.
  2. For an electrical saw, you must consider the weather condition because if you’re working in rainy or wet weather, it might ruin your electrical saw.
  3. Call a pro if the thickest part of the branches is more than 8 inches. Avoid cutting down trees near or overhead electricity wires. Removal of this nature should be left to the experts.
  4. Using external force is not recommended. Relax and let the pole saw do its thing. It prevents damage to the knife’s blade. Applying force might break the blade.
  5. If the weather is bad, you might have to abandon your plans. The chain on your pole saw might go rusty if exposed to dampness. A windy or wet day should be avoided at all costs.


  • Does it make sense to invest in a pole saw?

While pole saws can simplify many trimming tasks, they aren’t always the best choice. Therefore, a pole saw may not be necessary if you simply need to trim small branches, vines, or leaves. If you want to chop 2 to 8-inch tree limbs, a pole saw may work.

  • Is a pole saw interchangeable with a chainsaw?

A pole saw can substitute for a chainsaw. Like the chainsaw, the pole saw is a variant. It offers a range of variants, each of which provides the user with an enhanced, optimized, and streamlined experience.

  • Can a pole saw be used to fall a tree?

It is much easier to reach high up in the tree using a pole saw. You may secure it around a branch and saw steadily for precise, clean cuts. As with other pruning equipment, pole saws come in different sizes; select one that fits your tree’s branches. 

  • Do you recommend a gas pole saw or an electric one?

A gas pole saw is preferable to a conventional saw if you require a strong saw to cut thick branches and need to cover a broad area. However, an electric pole saw is preferable if you want to do a quiet and compact activity on your lawn.


After reading, do you still find it difficult to assemble a gas pole saw? You just need to know some basic steps and you’ll get to know how to assemble a gas pole saw. 

However, be more careful when choosing a gas pole saw because a faulty one can be dangerous for you, as mentioned several times.

Devid Jhon

Hello, I am devid jhon from California, I have 12 years experience in power tools and gardening equipment. This is my personal blog, before writing an article I was fully researching about article topic and it's equipment, so I ensure my visitors, you can easily trust my articles.

Click Here to Leave a Comment Below 0 comments